Price: $21.99
(as of Feb 16, 2025 16:53:43 UTC – Details)
Product Description
How to Install (Pls record the fingerprint before installing):
1. Fixed the Part A in proper place with two large silver screws (cabinet side / upper edge, upper edge of drawer)2. Drill a 15 mm diameter round hole in the proper position on the outside board of the drawer/cabinet and then put the fingerprint panel in the hole. Note: Put the prompt lamp on the up side.3. At the other end of the board, pass the wire through the metal gasket and use two small yellow screws to fix the gasket and the fingerprint panel. Then connect the line to the lock box correctly.4. Use two big silver screws to secure the lock box in place (screw length is freely chosen according to board thickness)5. Here we done! Check whether the distance is appropriate and whether it can lock normally.
Why Choose SUMNEW Lock!!!
0.5s Quick Unlock & Auto Pop-up
Leading fingerprint tech, unlock only needs 0.5 S reaction time.
And the latch will pops up automatically after unlocking to prevent you from forgetting to lock.
Smart AI
Record up to 40 fingerprints.
The fingerprints recorded are the only keys! No need any extra cards, keys, APP or bluetooth connection.
Support Emergency Charge
Humanized design! Support USB cable emergency charge, do not need to worry about low power can not unlock.
SUMNEW TECH
SUMNEW Fingerprint Cabinet Lock= Reliable Factory + Fastest Transportation + Perfect Quality + Considerate Service
Fingerprints Enroll Instruction:
Step 1
Long press the sensor for about 10 seconds until the blue light on;Now it is in enroll mode, let’s begin: Use same finger enrolls 5 times at different angles. Then the green light on, it indicates that the first fingerprint was successfully recorded. Step 2
Then the blue light on again. It’s still in enrolling mode. If you need to record more fingerprints, just repeat the second step. 5 seconds no operation it will automatically quit enroll status) Note:
When you receive the lock, it is brand new and any fingerprint can open it！ Remember to enroll your fingerprints before use!To ensure the lock works well, it’s better to enroll no less than 3 different fingerprints.
Package includes: ✔ Lock Body ✔ Lock Catch ✔ Fingerprint Panel ✔ Screws & Accessories ✔ User Manuel ✖ Battery ✖ Charging Cable
Humanized Electricity Tips
When the battery power is low, the lock will flicker red light. Then you can replace the AAA batteries in time. (Attention: our lock do not include Batteries and Charging Cable)Delete Fingerprints and Restore Factory Settings： Long press set switch, blue light on, red light after three seconds, release switch. All fingerprints were removed successfully.
Fingerprint Cabinet Lock for home
FAQs and Solutions
Question 1: why could all fingerprints unlock it?–Answer: ‘Cause the lock is still in original state and you haven’t enroll any fingerprint in it. So anyone any fingerprints can open it.–Solution: Enroll your personal fingerprints correctly by following the instructions/videos .Question 2: why is fingerprint identification slow?–Answer: ‘Cause the fingerprint haven’t been recorded clearly and completely, it may cause slow identification.–Solution: Re-enroll with the same finger at different angles.Question 3: How to unlock when it is out of battery?–Answer: Don’t worry, there’s still plan B. And The lock will have a red light flicker prompt to remind you that it’s time to change new battery. –Solution: Use your power bank to power it and unlock! Question 4: How to enroll multiple fingerprints?–Answer: Same thing, enroll one fingerprint successfully and repeat the steps. Up to 20 fingerprints can be enrolled. Question 5: How do delete fingerprints?–Answer: Hold down setting switch continuously untill red light on 3 seconds (you will see blue lights first and the red lights). There we done!
Quick Unlock: Advanced fingerprint lock tech with better response and sensitivity. 0.5 S reaction time, unlock just in a blink. Don’t need any extra cards, keys, APP or bluetooth connection. Your fingerprints are the only keys
Auto Lock: The lock tongue will pops up automatically after unlocking for a period of time to prevent you from forgetting to lock. Perfect solution to your occasional carelessness! Modern life without trouble
Privacy Protection: More secure! Our fingerprint lock is definitely your choice to improve the safety of personal items and secrets! It can effectively prevent your files from getting messed up or items from being damaged
Emergency Charge: The cabinet lock can record up to 20 fingerprints. Support USB cable emergency charge, do not need to worry about low power can not unlock. Please Note: Micro cable and AAA batteries are not included! Have to buy separately
Wide Application: Our smart biometric lock can be widely used in wood furniture, such as wardrobe, drawer, Cabinet, storage boxes and so on
Easy installation: As long as your furniture thickness is appropriate, it can be applied perfectly. Enjoy the fun of making it yourself
Customers say
Customers are satisfied with the lock’s functionality and design. They find it secure and a good low-security way to put up a barrier to entry. However, some customers feel the build quality is poor and the product feels cheap and flimsy. Opinions differ on installation, fingerprint reader accuracy, and security.
AI-generated from the text of customer reviews
Lucas Rossi –
Works well for its purpose, recommended.
Let me start by saying that you should keep your expectations at bay: it’s a $25 plastic fingerprint lock. It’s perfect for keeping things out of reach of children, for example. If you’re trying to keep valuables safe from burglars, you need a proper safe and not this product. It would be quite easy for a mildly-skilled adult to open this lock with a simple bent metal tool, or for anyone over 12 y/o with a screwdriver to pry it open, so keep that in mind.Having said that, it works very well after setting up the fingerprints (which is not as hard as some reviewers say it is – procedure below). It also comes with a USB-C key that can be used to unlock it if you have problems (it’ll allow any finger to open it once inserted), which looks just like a USB adapter, so it’s inconspicuous. Just make sure to keep the key in a safe place (and not inside where this lock is installed, obviously).How to add fingerprints:1) As soon as you plug the sensor into the lock and install batteries for the first time, the lock will open with any fingerprint. Start by holding a finger on the sensor. The lock will open, then close, and then the LED will stay blue. That means it’s ready to program.2) Repeatedly scan the new fingerprint you want to add (touch and remove) until the LED stays green for longer and then turns blue again. 5 successful scans are needed for each finger you want to add. Note: Make sure to change the position of the finger on the sensor ever so slightly, to make sure it’s less sensitive to small changes in finger position. If you get a red LED it means that scan failed or the finger is already registered.3) Once the LED turns blue (after 5 successful scans), start scanning a different fingerprint right away.4) Repeat until you scanned all fingerprints you want to register, then just wait for a few seconds and it’ll get out of programming mode by itself.Note: If you take too long to scan a new finger and it gets out of programming mode, use an already scanned finger to re-enter programming mode (step 1). This is also how you add more fingerprints later on.If the lock isn’t opening with any finger when you insert batteries on it for the first time, I’m not sure but you might be able to use the supplied key to enable any finger, and then reset the lock (remove all fingerprints). Check the manual, there’s a reset procedure there with LED colors to watch for.Installation requires low to average skills, mainly because getting the lock itself bolted at the correct height might be challenging for someone who’s never done any DIY. Other than that, drilling the hole for the fingerprint reader is easy. Just be careful when drilling through IKEA furniture, because those are basically glued sawdust, so it might be best to drill a pilot hole through and then drill from both sides to prevent it from looking like a bullet exit hole from the other side, which can make it tricky to bolt the reader in place.It works very fast, even though it might require a second attempt every 2 or 3 times. I’m sure if I program the same finger at a different position it’ll be much better. But again: it’s a $25 fingerprint lock.Only issue I had is that it was missing a couple of screws to bolt the reader to the furniture, but that’s not a big deal.
Jeffrey Pua –
Works great !
great little gadget . i bought a file cabinet to go under my new workstation table . it was the only white one i could find with the strict dimensions to fit under , however it didn’t have a lock . i at least wanted one drawer to lock for out of sight paper work from the cleaning person that comes to my house and my kids. this really did the trick , wish it came in a white to match my cabinet however it still looks kinda cool like a mini camera :)the product itself works great. for all the reviews that peope said it wouldn’t register the finger print and anyone can open it , it’s because you are not registering the fingerprint correctly . that part was extremely tricky for me becasue i’m not a technical person however my 11 year old son who’s a computer genius helped me through that process . Don’t drill the hole too big otherwise the fingerprint pad will be too loose on the cabinet and won’t look right . took about an hour from start to finish and lining up the 2 pieces and making sure it matched on properly also took a bit of time and precision . mai definitely took a bit of time to get it to perfection . otherwise , great product and works well for what i need it for !
Casey (Boston) –
After 3 years of heavy daily use still perfect.
I’m sorry, but anyone that is saying they have issues with the installation and/or recording fingerprints is either fibbing or should not be allowed to do any diy projects themselves. You are basically saying you cant drill a hole (for the installation), and can’t hold a finger on the scanner for 10 seconds (to register).I purchased this lock just about 3 years ago, the photo is after the 3 years of heavy use. I have it installed on my desks center top drawer that I am in and out of all day long. I have replaced the batteries twice now (the second time just recently) And I can count on 1 hand the number of times it didn’t correctly read my print on the first try, and every one was because I had something (glue, food, dirt) on my finger. There is honestly no difference between now and the day I installed it.This is probably the third time Ive left any review on a product. After 3 years, heavy use, and for this price, I figured it was well earned. And thank you.
NEIL –
Not Bluetooth as headline
Works good. Easy to program.The E Key works good.NOT BLUETOOTH AS DESCRIBED
Daniel Lewis –
Almost impossible to properly install, and then registering the fingerprint doesn’t work.
Who has a drill bit that will drill a 16mm hole in something? Not me. After a half-hour getting a hole into a drawer front, it became clear that the inserted finger reader has to fit precisely, or the reader won’t stay seated in its hole. Finally worked that out. And then, the instructions — written in almost incomprehensible English — didn’t work. Returning the three of these I bought tomorrow.
greg matlack –
good drawer lock
Product works every time
Jason M –
Great for quick access and safety
I like to keep a certain item for protection in my night stand drawer, but more importantly, this helps keep it out of reach from the grandkids, yet I can still get to it quickly in an emergency. At first glance, it seemed difficult to install, but once I got going, it made sense. I may order another.
jessuca –
Works as advertised. Small flimsy will not secure anything you could break it with a finger pull.
Understand you are getting what you paid for. Its a very cheap small flimsy lock that could be broken with finger strength. That bein said if your using it as its advertised it does work great. For a non strength security requirement say a hidden cabinet or drawer or something you dont need real security for it works great. The fingerprint reader works well.
reddy –
Easy to install, battery life is good,low and best price
Rajsekhar Dabburi –
Basic criteria of a lock is it should be strong and sturdy, this is made of very bad quality plastic and the electronics do not look reliable at all. And the lock does not even fix properly due to its poor quality and the wires are so thin, it will just break. Disappointing product. Amazon should stop Indian companies selling cheap quality Chinese products as their own.
Okk –
Works very well, easy to use and the team is very supportive they coordinated how to setup (add/remove fingerprints)
Punit Malhotra –
This lock is actually very good. Works smoothly so far. It makes life very easy and convenient.Need a carpenter to instal it.Good after sales service as well
Vishal Sharma –
For WFH, pur laptop and other office stuff, very usefull thumbprint scan drawer